← All articles

Machining Phenolic: Canvas vs Linen, Moisture and Edges

November 17, 2026 · 7 min read

Phenolic is one of the oldest engineering laminates still in everyday use, and it is still specified for good reasons: it insulates, it wears well, it runs quietly as a gear, and it does not soften as it warms the way a thermoplastic does. It is also the material where a part that measured right on the machine can be out the following week, because the cotton fabric inside it takes up water from the air.

Here is how phenolic laminate behaves at the cutter and afterwards, and how to design and specify a part that comes out clean and stays on size.

What phenolic laminate is

Phenolic laminate is layers of fabric soaked in phenolic resin, then pressed and cured into sheet, rod or tube. It is a thermoset: once cured, it does not melt, so heat at the cutter burns or chars it rather than smearing it the way it smears a thermoplastic.

The fabric decides the grade. We stock the two cotton-fabric grades engineers specify most often:

  • Canvas is the coarser, heavier weave. It is the tougher grade, the one chosen for gears, bushings, wear pads and parts that take a knock.
  • Linen is a finer weave. It machines to a smoother finish and holds small features and fine detail better, so it is the usual choice for small, detailed parts and close work.

In the NEMA grade names, canvas is C and linen is L; the CE and LE grades are the versions made for electrical use, with better electrical properties and lower moisture absorption. The values below are the canvas-grade rows on our phenolic material page, from the Norplex-Micarta NP310E (grade CE) data bulletin:

Property Canvas phenolic (NP310E, CE, typical) What it means at the machine
Tensile strength, ultimate (ASTM D638, lengthwise) 11,000 psi A laminate has no yield point; this is the breaking value
Flexural modulus (ASTM D790, lengthwise) 1,600,000 psi Stiff for a non-glass material; thin sections still need support
Hardness (ASTM D785) Rockwell M100 Hard, and the fabric makes it abrasive to tooling
Water absorption, 24 h (ASTM D570) 2.0 % High; this is the number that moves the size
Thermal expansion, in-plane (IPC-TM-650 2.4.24) 1.11 × 10⁻⁵ in/in/°F Low, well below unreinforced plastics

Treat these as typical published values for one maker's canvas grade, not a specification. Crosswise strength and stiffness are lower and crosswise expansion is slightly higher; linen grades publish their own numbers.

Tooling: abrasive, but not glass

The cotton fabric and cured resin are abrasive. Phenolic dulls tooling noticeably faster than unfilled thermoplastics, though not at the rate of glass epoxy like G-10/FR-4.

  • Carbide is the sensible default. High-speed steel will cut phenolic, but carbide lasts longer and holds size more consistently from part to part, which matters on production runs.
  • Keep the edge sharp. A dull tool rubs instead of cutting. On phenolic, rubbing makes heat, and heat scorches the resin and frays the fabric at the edge.
  • Clear the dust from the cut. Phenolic dust packed into a slot or a drilled hole is recut, which heats the tool and the part.

The dust, not the chips

Phenolic does not make the curled chips a thermoplastic does; it makes fine dust and powdery cuttings of cured resin and fabric. That shapes how it is cut:

  • It is usually cut dry, with extraction at the tool. Capturing the dust at the cutter keeps it out of the air and off the machine.
  • Liquid coolant is the wrong fix for heat. The maker recommends cutting dry with air or vacuum at the cutter, because liquid coolant is hard to remove from finished parts, and the cotton fabric can absorb water (see the table).

Neither point is the buyer's problem to solve, but both are part of why a phenolic part is quoted differently from a thermoplastic part of the same shape.

Moisture is where the tolerance goes

This is the property that matters most on a print. Canvas phenolic in CE grade takes up about 2.0 % water in 24 hours of immersion, about nine times the 0.22 % of G-10 on the same test. The cotton fabric is the reason, and it means a phenolic part can change size with the humidity it lives in. Expect the size change to show most through the thickness and at cut edges, where the fabric ends are exposed.

What that means for a drawing:

  • Choose the grade with moisture in mind. CE and LE absorb less moisture than C and L, but even the CE figure above is about nine times G-10's. If the part sees humidity or wash-down and has to hold a fit, say so, and ask whether glass epoxy is the better material.
  • Say where it will be measured. A dimension gauged in a dry shop and again in a humid plant is two different numbers. Agree the inspection conditions for critical fits.
  • Allow running clearance on bushings and bearings. A phenolic bushing that will see water or humidity needs more clearance than an acetal one, because the bore can close as the material absorbs moisture.
  • Remember the machined edges. Cutting exposes the fabric ends, and an exposed edge takes up water faster than a pressed face. A part that will be wet in service is a reason to look hard at the grade, or at a different material.

Heat is the easier half. In-plane, phenolic expands far less than the unreinforced plastics on our plastic thermal expansion chart. A 24" canvas phenolic panel that warms 50 °F grows about 0.013" along the sheet (24 in × 11.1 µin/in·°F × 50 °F); the same panel in G-10 grows about 0.008" and in cast acrylic about 0.047".

Delamination and edge breakout

Like any laminate, phenolic fails along its layers, and it does so in predictable places:

  • Where the cutter exits. The last layer has nothing behind it and is pushed away instead of cut. Backing the material with a sacrificial plate supports it.
  • At the faces of a routed edge. An up-cut tool lifts the top layer and a down-cut tool pushes the bottom one; compression cutters cut toward the middle of the sheet from both faces and leave clean edges on sheet parts.
  • Where a drill breaks through. Support the work directly under the hole, keep the drill sharp, and ease the feed as the point breaks through.
  • At sharp outside corners. A small radius or chamfer keeps exposed corners from chipping in handling.

Design rules for phenolic parts

  • Load it in-plane. The fabric carries the load along the sheet. Through the thickness the part is held together by the resin between the layers, so it is weaker in that direction.
  • Keep threads out of the edge. A thread cut into the edge of the sheet, parallel to the layers, can split them. Threads through the face are the safer layout.
  • Use inserts for repeated assembly. Tapped threads in phenolic are fine for occasional assembly; a part that will be taken apart again and again is a candidate for threaded inserts.
  • Keep holes off the edge. A hole close to an edge leaves a thin web of laminate that can split when a fastener is tightened.
  • Pick linen for small detail. Fine teeth, small holes and thin webs come out cleaner in the finer weave.

When phenolic is the right call

  • Electrical insulators, terminal boards and standoffs in dry, indoor service.
  • Gears and rollers where quiet running matters.
  • Bushings, bearings and wear pads in industrial machinery, with clearance for moisture.
  • Parts that sit near heat that would move acetal or nylon, within phenolic's temperature rating.

When it is not

  • Wet or high-humidity service that must hold a fit. Moisture moves phenolic. G-10/FR-4 takes up far less water, and an unreinforced plastic like Delrin or UHMW may suit a wet wear part better.
  • Parts that must carry high loads while insulating. Glass epoxy is much stronger and stiffer.
  • Food contact. The cited data bulletin makes no food-contact statement for this grade.

How we quote phenolic parts

Send the drawing and tell us what the part does: canvas or linen (or whether you want our advice), whether it is an electrical or a mechanical part, what humidity and temperature it lives in, which dimensions are critical, and how the edges must look. We machine canvas and linen phenolic sheet, rod and tube to print in Linden, NJ, alongside the rest of the engineering plastics we have been CNC machining since 1968. Properties and stock forms are on our phenolic material page.

Request a quote · Plastic machining services

Have a plastics part to make?

We machine and fabricate engineering plastics for aerospace, medical, and semiconductor customers. Send us your print for a straight answer.

Request a Quote